skills based assesment in applied network Labs
Anonymous

Question Description

complete the Skills Based Assessment. The assessment document is attached to this post.

Here is what you need to do to get the Skills Based Assessment done..

 go to NetLab, “Scheduler”.This is the link:  http://cdclab.westwood.edu/

- Select the class.it should be the third class on the line ( 15 may ) Login -jachamfour , password- jimlotins

- Reserve lab time for yourself

- Scroll all the way down and select the “Reserve Multi-purpose Academy Pod (no lab exercise)”

- Select the time you need to schedule the lab

- On the “New Reservation” Window, check the Radio button at the bottom that reads “no configs loaded (clean)”

- Make sure to change the timing by giving yourself enough time.

- Click OK

When you enter the lab, don’t panic. The topology is different from the one you have on the Skills Based Assessment.

Here is what you need to do:

Since the PODs on NetLab use 3 routers and 3 switches, and since you only need 3 routers and 2 switches for the Skills Based Assessment, you can use the topology in the PODs with the following adjustments. If you make sure that you do the below correctly, your topology will be exactly as the one given to you on the Skills Based Assessment.

PC B become your Internet PC

On Router R1, keep S1 and E0 shut.
On Router R3, keep S0, E0, and E1 shut. You will configure Loopback interfaces instead.
The above will take the following connections out:

-  Between R1 and R3

-  Between R1 and PC A

-  Between R3 and PC C

-  Between R3 and S3

On Router R2, keep E1 shut. You will configure the Loopback interface that connects to the Web Server.

On the Switches:

S1 remains connected to PC A through its E6.
On S1, shut down E1, E2, and E4.
E3 remains open, which becomes the Trunk connected to S3.

S3 remains connected to PC C through E18
On S3, shut down E1, E2, and E4.
E3 remains open, which becomes the Trunk connected to S1.

Since you are not going to use S2, make sure that the E18 on S2 is shut. This way, PC B is only connected to the router R2.

Complete the Skills Based Assessment.


- Save your router configurations on a text, or Word, file. You have to include those when you submit the Assessment. You can either include them at the bottom of your assessment sheet, or you can include them on a separate file.


- Complete the Assessment sheet and submit it.


- Make sure to submit all your IP addressing as well. THIS IS A MUST

Best of luck and please let me know if you have any question.

SkillsAssessment-Student_Exam.docx




Unformatted Attachment Preview

CCNA: Routing and Switching Essentials Skills Assessment – Student Training Exam Topology Assessment Objectives Part 1: Initialize Devices (8 points, 5 minutes) Part 2: Configure Device Basic Settings (28 points, 30 minutes) Part 3: Configure Switch Security, VLANs, and Inter-VLAN Routing (14 points, 15 minutes) Part 4: Configure OSPFv2 Dynamic Routing Protocol (24 points, 25 minutes) Part 5: Implement DHCP and NAT (13 points, 25 minutes) Part 6: Configure and Verify Access Control Lists (ACLs) (13 points, 25 minutes) © 2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 1 of 14 CCNA: Routing and Switching Essentials SA Exam Scenario In this Skills Assessment (SA) you will configure a small network. You will configure routers, switches, and PCs to support IPv4 connectivity, switch security, and inter VLAN routing. You will then configure the devices with OSPFv2, DHCP, and dynamic and static NAT. Access control lists (ACLs) will be applied for added security. You will test and document the network using common CLI commands throughout the assessment. Required Resources • 3 Routers (Cisco 1941 with Cisco IOS Release 15.2(4)M3 universal image or comparable) • 2 Switches (Cisco 2960 with Cisco IOS Release 15.0(2) lanbasek9 image or comparable) • 3 PCs (Windows 7, Vista, or XP with terminal emulation program, such as Tera Term) • Console cable to configure the Cisco IOS devices via the console ports • Ethernet and Serial cables as shown in the topology Part 1: Initialize Devices Total points: 8 Time: 5 minutes Step 1: Initialize and reload the routers and switches. Erase the startup configurations reload the devices. Before proceeding, have your instructor verify device initializations. Task IOS Command Points Erase the startup-config file on all routers. 1½ points (½ point per router) Reload all routers. 1½ points (½ point per router) Erase the startup-config file on all switches and remove the old VLAN database. 2 points (1 point per switch) Reload both switches. 2 points (1 point per switch) Verify VLAN database is absent from flash on both switches. 1 point (½ point per switch) Instructor Sign-off Part 1: _________________________ Points: __________ of 8 © 2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 2 of 14 CCNA: Routing and Switching Essentials SA Exam Part 2: Configure Device Basic Settings Total points: 28 Time: 30 minutes Step 1: Configure the Internet PC. Configuration tasks for the Internet PC include the following (Refer to Topology for IP address information): Configuration Item or Task Specification Points IP Address (1/2 point) Subnet Mask (1/2 point) Default Gateway 209.165.200.225 Note: It may be necessary to disable the PC firewall for pings to be successful later in this lab. Step 2: Configure R1. Configuration tasks for R1 include the following: Configuration Item or Task Specification Disable DNS lookup Points (1/2 point) Router name R1 (1/2 point) Encrypted privileged exec password class (1/2 point) Console access password cisco (1/2 point) Telnet access password cisco (1/2 point) Encrypt the clear text passwords (1/2 point) MOTD banner Unauthorized Access is Prohibited! (1/2 point) Interface S0/0/0 Set the description Set the Layer 3 IPv4 address. Use the first available address in the subnet. Set the clocking rate to 128000 Activate Interface (1/2 point) Default route Configure a default route out S0/0/0. (1/2 point) Note: Do not configure G0/1 at this time. Step 3: Configure R2. Configuration tasks for R2 include the following: © 2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 3 of 14 CCNA: Routing and Switching Essentials SA Exam Configuration Item or Task Specification Disable DNS lookup Points (1/2 point) Router name R2 (1/2 point) Encrypted privileged exec password class (1/2 point) Console access password cisco (1/2 point) Telnet access password cisco (1/2 point) Encrypt the clear text passwords (1/2 point) Enable HTTP server (1/2 point) MOTD banner Unauthorized Access is Prohibited! (1/2 point) Interface S0/0/0 Set the description Set the Layer 3 IPv4 address. Use the next available address in the subnet. Activate Interface (1 point) Interface S0/0/1 Set the description Set the Layer 3 IPv4 address. Use the first available address in the subnet. Set clocking rate to 128000 Activate Interface (1 point) Interface G0/0 (Simulated Internet) Set the Description Set the Layer 3 IPv4 address. Use the first available address in the subnet. Activate Interface (1 point) Interface Loopback 0 (Simulated Web Server) Set the description. Set the Layer 3 IPv4 address. (1/2 point) Default route Configure a default route out G0/0. (1/2 point) Step 4: Configure R3. Configuration tasks for R3 include the following: © 2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 4 of 14 CCNA: Routing and Switching Essentials Configuration Item or Task SA Exam Specification Disable DNS lookup Points (1/2 point) Router name R3 (1/2 point) Encrypted privileged exec password class (1/2 point) Console access password cisco (1/2 point) Telnet access password cisco (1/2 point) Encrypt the clear text passwords (1/2 point) MOTD banner Unauthorized Access is Prohibited! (1/2 point) Interface S0/0/1 Set the description Set the Layer 3 IPv4 address. Use the next available address in the subnet. Activate Interface (1/2 point) Interface Loopback 4 Set the Layer 3 IPv4 address. Use the first available address in the subnet. (1/2 point) Interface Loopback 5 Set the Layer 3 IPv4 address. Use the first available address in the subnet. (1/2 point) Interface Loopback 6 Set the Layer 3 IPv4 address. Use the first available address in the subnet. (1/2 point) Default route Configure a default route out S0/0/1. (1/2 point) Step 5: Configure S1. Configuration tasks for S1 include the following: Configuration Item or Task Specification Disable DNS lookup Points (1/2 point) Switch name S1 (1/2 point) Encrypted privileged exec password class (1/2 point) Console access password cisco (1/2 point) Telnet access password cisco (1/2 point) Encrypt the clear text passwords MOTD banner (1/2 point) Unauthorized Access is Prohibited! (1/2 point) Step 6: Configure S3 Configuration tasks for S3 include the following: © 2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 5 of 14 CCNA: Routing and Switching Essentials SA Exam Configuration Item or Task Specification Disable DNS lookup Points (1/2 point) Switch name S3 (1/2 point) Encrypted privileged exec password class (1/2 point) Console access password cisco (1/2 point) Telnet access password cisco (1/2 point) Encrypt the clear text passwords MOTD banner (1/2 point) Unauthorized Access is Prohibited! (1/2 point) Step 7: Verify network connectivity. Use the ping command to test connectivity between network devices. Use the following table to methodically verify connectivity with each network device. Take corrective action to establish connectivity if a test fails: From To IP Address Ping Results Points R1 R2, S0/0/0 (1/2 point) R2 R3, S0/0/1 (1/2 point) Internet PC Default Gateway (1/2 point) Note: It may be necessary to disable the PC firewall for pings to be successful. Instructor Sign-off Part 2: ______________________ Points: _________ of 28 Part 3: Configure Switch Security, VLANS, and Inter VLAN Routing Total points: 14 Time: 15 minutes Step 1: Configure S1. Configuration tasks for S1 include the following: © 2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 6 of 14 CCNA: Routing and Switching Essentials Configuration Item or Task SA Exam Specification Points Create the VLAN database Use Topology VLAN Key table to create and name each of the listed VLANS. (1 point) Assign the management IP address. Assign the Layer 3 IPv4 address to the Management VLAN. Use the IP address assigned to S1 in the Topology diagram. (1/2 point) Assign the default-gateway Assign the first IP address in the subnet as the default-gateway. (1/2 point) Force trunking on Interface F0/3 Use VLAN 1 as the native VLAN. (1/2 point) Force trunking on Interface F0/5 Use VLAN 1 as the native VLAN. (1/2 point) Configure all other ports as access ports Use the interface range command. (1/2 point) Assign F0/6 to VLAN 31 (1/2 point) Shutdown all unused ports. (1/2 point) Step 2: Configure S3. Configuration tasks for S3 include the following: Configuration Item or Task Specification Points Create the VLAN database Use Topology VLAN Key Table to create each of the listed VLANS. Name each VLAN. (1 point) Assign the management IP address. Assign the Layer 3 IPv4 address to the Management VLAN. Use the IP address assigned to S3 in the Topology diagram. (1/2 point) Assign the default-gateway Assign the first IP address in the subnet as the default-gateway (1/2 point) Force trunking on Interface F0/3 Use VLAN 1 as the native VLAN. (1/2 point) Configure all other ports as access ports Use the interface range command. (1/2 point) Assign F0/18 to VLAN 33 (1/2 point) Shutdown all unused ports. (1/2 point) Step 3: Configure R1. Configuration tasks for R1 include the following: © 2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 7 of 14 CCNA: Routing and Switching Essentials SA Exam Configuration Item or Task Specification Points Configure 802.1Q subinterface .31 on G0/1 Description Accounting LAN Assign VLAN 31. Assign the first available address to this interface. (1 point) Configure 802.1Q subinterface .33 on G0/1 Description Engineering LAN Assign VLAN 33. Assign the first available address to this interface. (1 point) Configure 802.1Q subinterface .99 on G0/1 Description Management LAN Assign VLAN 99. Assign the first available address to this interface. (1 point) Activate Interface G0/1 (1/2 point) Step 4: Verify network connectivity. Use the ping command to test connectivity between the switches and R1. Use the following table to methodically verify connectivity with each network device. Take corrective action to establish connectivity if a test fails: From To IP Address Ping Results Points S1 R1, VLAN 99 address (1/2 point) S3 R1, VLAN 99 address (1/2 point) S1 R1, VLAN 31 address (1/2 point) S3 R1, VLAN 33 address (1/2 point) Instructor Sign-off Part 2: ______________________ Points: _________ of 14 Part 4: Configure OSPFv2 Dynamic Routing Protocol Total points: 24 Time: 25 minutes Step 1: Configure OSPFv2 on R1. Configuration tasks for R1 include the following: © 2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 8 of 14 CCNA: Routing and Switching Essentials SA Exam Configuration Item or Task Specification Points OSPF Process ID 1 (1/2 point) Router ID 1.1.1.1 (1/2 point) (1 point) Advertise directly connected Networks Use classless network addresses Assign all directly connected networks to Area 0 Set all LAN interfaces as passive (1 point) Change the default cost reference bandwidth to support Gigabit interface calculations 1000 Set the serial interface bandwidth 128 Kb/s (1 point) Adjust the metric cost of S0/0/0 Cost: 7500 (1 point) (1 point) Step 2: Configure OSPFv2 on R2. Configuration tasks for R2 include the following: Configuration Item or Task Specification Points OSPF Process ID 1 (1 point) Router ID 2.2.2.2 (1 point) Advertise directly connected Networks Use classless network addresses Note: Omit the G0/0 network. (1 point) Set the LAN (Loopback) interface as passive (1 point) Change the default cost reference bandwidth to allow for Gigabit interfaces 1000 Set the bandwidth on all serial interfaces 128 Kb/s (1 point) Adjust the metric cost of S0/0/0 Cost: 7500 (1 point) (1 point) Step 3: Configure OSPFv2 on R3. Configuration tasks for R3 include the following: © 2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 9 of 14 CCNA: Routing and Switching Essentials SA Exam Configuration Item or Task Specification Points OSPF Process ID 1 (1/2 point) Router ID 3.3.3.3 (1/2 point) (1 point) Advertise directly connected Networks Use classless network addresses Assign interfaces to Area 0 Use a single summary address for the LAN (loopback) interfaces. Set all LAN (Loopback) interfaces as passive (1 point) Change the default cost reference bandwidth to support Gigabit interface calculations 1000 Set the serial interface bandwidth 128 Kb/s (1 point) (1 point) Step 4: Verify OSPF information. Verify that OSPF is functioning as expected. Enter the appropriate CLI command to discover the following information: Question Response Points What command will display all connected OSPFv2 routers? (1 point) What command displays a summary list of OSPF interfaces that includes a column for the cost of each interface? (1 point) What command displays the OSPF Process ID, Router ID, Address summarizations, Routing Networks, and passive interfaces configured on a router? (1 point) What command displays only OSPF routes? (1 point) What command displays detail information about the OSPF interfaces, including the authentication method? (1 point) What command displays the OSPF section of the runningconfiguration? (1 point) Instructor Sign-off Part 3: ______________________ Points: _________ of 24 Part 5: Implement DHCP and NAT for IPv4 Total points: 13 Time: 25 minutes Step 1: Configure R1 as the DHCP server for VLANs 31 and 33. Configuration tasks for R1 include the following: © 2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 10 of 14 CCNA: Routing and Switching Essentials SA Exam Configuration Item or Task Specification Points Reserve the first 20 IP addresses in VLAN 31 for static configurations (1 point) Reserve the first 20 IP addresses in VLAN 33 for static configurations (1 point) Create a DHCP pool for VLAN 31 Name: ACCT DNS-Server: 10.10.10.11 Domain-Name: ccna-sba.com Set the default gateway. (1 point) Create a DHCP pool for VLAN 33 Name: ENGNR DNS-Server: 10.10.10.11 Domain-Name: ccna-sba.com Set the default gateway. (1 point) Step 2: Configure Static and Dynamic NAT on R2. Configuration tasks for R2 include the following: Configuration Item or Task Create a local database with 1 user account Specification Username: webuser Password: cisco12345 Privilege level: 15 Points (1 point) Enable HTTP server service (1/2 point) Configure the HTTP server to use the local database for authentication (1/2 point) Create a static NAT to the Web Server Inside Global Address: 209.165.200.229 Assign the inside and outside interface for the static NAT (1 point) (1 point) Configure the dynamic NAT inside private ACL Access List: 1 Allow the Accounting and Engineering networks on R1 to be translated. Allow a summary of the LANs (loopback) networks on R3 to be translated. (1 point) Define the pool of usable public IP addresses Pool Name: INTERNET Pool of addresses include: 209.165.200.225 – 209.165.200.228 (1 point) Define the dynamic NAT translation © 2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. (1 point) Page 11 of 14 CCNA: Routing and Switching Essentials SA Exam Step 3: Verify DHCP and Static NAT. Use the following tasks to verify that DHCP and Static NAT settings are functioning correctly. It may be necessary to disable the PC firewall for pings to be successful: Test Results Points Verify that PC-A acquired IP information from the DHCP server (1/2 point) Verify that PC-C acquired IP information from the DHCP server (1/2 point) Verify that PC-A can ping PC-C. Note: It may be necessary to disable the PC firewall (1/2 point) Use a Web browser on the Internet PC to access the Web server (209.165.200.229). Login with Username: webuser, Password: cisco12345 (1/2 point) Note: Verification of dynamic NAT will be performed in Part 6. Instructor Sign-off Part 2: ______________________ Points: _________ of 13 Part 6: Configure and Verify Access Control Lists (ACLs) Total points: 13 Time: 25 minutes Step 1: Restrict access to VTY lines on R2. Configuration Item or Task Configure a named access list to only allow R1 to telnet to R2. Specification ACL Name: ADMIN-MGT Points (2 points) Apply the named ACL to the VTY lines (1 point) Verify ACL is working as expected, (1 point) Step 2: Secure the network from Internet traffic. © 2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 12 of 14 CCNA: Routing and Switching Essentials SA Exam Configuration Item or Task Specification Configure an Extended ACL to: Points (2 points) ACL No.: 101 • Allow Internet hosts WWW access to the simulated web server on R2 by accessing the static NAT address (209.165.200.229) that you configured in Part 3. • Prevent traffic from the Internet from pinging internal networks, while continuing to allow LAN interfaces to ping the Internet PC. Apply ACL to the appropriate interface(s) (1 point) Verify ACL is working as expected (1 point) From the Internet PC: • Ping PC-A (Pings should be unreachable.) • Ping PC-C (Pings should be unreachable.) From R1, Ping the Internet PC (Pings should be successful.) Note: It may be necessary to disable the PC firewall for pings to be successful. Step 3: Enter the appropriate CLI command needed to display the following: Command Description Student Input (command) Points Display the matches an access-list has received since the last reset. (1 point) Reset access-list counters. (1 point) What command is used to display what ACL is applied to an interface and the direction that it is applied (1 point) What command displays the NAT translations? Note: The translations for PC-A and PC-C were added to the table when the Internet PC attempted to ping these PCs in Step 2. Pinging the Internet PC from PC-A or PCC will not add the translations to the table because of the way the Internet is being simulated on the network. What command is used to clear dynamic NAT translations? (1 point) (1 point) Instructor Sign-off Part 4: ______________________ Points: _________ of 13 © 2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 13 of 14 CCNA: Routing and Switching Essentials SA Exam Part 7: Cleanup NOTE: DO NOT PROCEED WITH CLEANUP UNTIL YOUR INSTRUCTOR HAS GRADED YOUR SKILLS EXAM AND HAS INFORMED YOU THAT YOU MAY BEGIN CLEANUP. Before turning off power to the routers, remove the NVRAM configuration files (if saved) from all devices. Disconnect and neatly put away all cables that were used in the Final. Router Interface Summary Table Router Interface Summary Router Model Ethernet Interface #1 Ethernet Interface #2 Serial Interface #1 Serial Interface #2 1800 Fast Ethernet 0/0 (F0/0) Fast Ethernet 0/1 (F0/1) Serial 0/0/0 (S0/0/0) Serial 0/0/1 (S0/0/1) 1900 Gigabit Ethernet 0/0 (G0/0) Gigabit Ethernet 0/1 (G0/1) Serial 0/0/0 (S0/0/0) Serial 0/0/1 (S0/0/1) 2801 Fast Ethernet 0/0 (F0/0) Fast Ethernet 0/1 (F0/1) Serial 0/1/0 (S0/1/0) Serial 0/1/1 (S0/0/1) 2811 Fast Ethernet 0/0 (F0/0) Fast Ethernet 0/1 (F0/1) Serial 0/0/0 (S0/0/0) Serial 0/0/1 (S0/0/1) 2900 Gigabit Ethernet 0/0 (G0/0) Gigabit Ethernet 0/1 (G0/1) Serial 0/0/0 (S0/0/0) Serial 0/0/1 (S0/0/1) Note: To find out how the router is configured, look at the interfaces to identify the type of router and how many interfaces the router has. Th ...
Purchase answer to see full attachment

Final Answer

mumkin1 (38)
Carnegie Mellon University

Anonymous
Solid work, thanks.

Anonymous
The tutor was great. I’m satisfied with the service.

Anonymous
Goes above and beyond expectations !

Studypool
4.7
Trustpilot
4.5
Sitejabber
4.4

Brown University





1271 Tutors

California Institute of Technology




2131 Tutors

Carnegie Mellon University




982 Tutors

Columbia University





1256 Tutors

Dartmouth University





2113 Tutors

Emory University





2279 Tutors

Harvard University





599 Tutors

Massachusetts Institute of Technology



2319 Tutors

New York University





1645 Tutors

Notre Dam University





1911 Tutors

Oklahoma University





2122 Tutors

Pennsylvania State University





932 Tutors

Princeton University





1211 Tutors

Stanford University





983 Tutors

University of California





1282 Tutors

Oxford University





123 Tutors

Yale University





2325 Tutors