Business Finance
Foothill College Wireless Charging Sterilizing Box Operating Instruction Worksheet 4

Foothill College

Question Description

I need an explanation for this Marketing question to help me study.

need to edit the specification and make it looks like more American native specification

Please pay attention to this specification and make it looks good and perfect.

only need to edit the english versions part

Unformatted Attachment Preview

感谢您购买手机无线充电除菌盒。使用本产品前,请仔细阅读 本产品说明书。 规格参数 产品名称:手机无线充电除菌盒 产品型号:OJD-L03 输入:5V/2A;9V/2A 无线充输出:10W(Max) 紫外线输出:2W(Max) 产品尺寸:210*120*62MM 产品重量:300g 颜色:雪山白 材质:ABS+PC 额定频率:110-205KHz 无线充转换率:73% 传输距离:≤6MM 产品清单 手机无线充电除菌盒 使用说明书 手机无线充电除菌盒x1 Type-C数据线(1米)x1 说明书x1 吸管x2 快速上手指南 1、插入配备的数据线,接通电源,产品通电后默认无线充电模 式,指示灯为红色,空载状态下直亮30秒后熄灭进入待机状 态。 2、将需要除菌的物品放入除菌盒,盖上盖子,除菌模式有如下 两种: ①18分钟除菌模式:短按一次盖子上方按键,此时会听到蜂鸣 器响“嘀”一声,绿色指示灯亮起,开始进入18分钟除菌模式。 ②30分钟除菌模式:短按两次盖子上方按键,此时会听到蜂鸣 器响“嘀”“嘀”两声,蓝色指示灯亮起,开始进入30分钟除菌 3、除菌在18分钟或30分钟完成后,内置蜂鸣器将会连续响三 声“嘀”“嘀”“嘀”。 除菌 1、将手机或其他待除菌的物品放入盒内,合上盖子。 4、香薰除菌功能:除菌前,使用配备的吸管将2或3滴香水滴入 盒内的香薰孔中,进行香薰除菌。 5、无线充电功能:将手机放置在上盖中间标识处可进行无线 充电,在无线充电工作状态下,红色指示灯直亮显示。 6、无线充电可与消毒模式同时作业,同时工作时,按键指示灯 会呈“红绿色”或“红蓝色”显示。 2、18分钟除菌模式:短按一次盖子上方按键,内置蜂鸣器响“嘀” 一声,绿色指示灯呈直亮状态,同时盒内的紫外线灯会亮起进 行消毒作业,当蜂鸣器连续响“嘀嘀嘀”三声时,表示除菌结束。 3、30分钟除菌模式:短按两次盖子上方按键,内置蜂鸣器响“嘀” “嘀”两声,蓝色指示灯呈直亮状态,同时盒内的紫外线灯会亮 详细使用说明: 起进行除菌作业,当蜂鸣器连续响“嘀嘀嘀”三声时,表示除菌 接通电源 结束。 ①在使用之前,请插入配备的数据线,接通电源,产品通电后 默认无线充电模式,指示灯为红色,空载状态下直亮30秒后 熄灭进入待机状态。 4、完成除菌:整个除菌过程为18分钟或30分钟,除菌作业完成后, 此时蜂鸣器会连续响“嘀嘀嘀”三声,表示作业自动结束。此时可 ②如红灯未亮起,请检查充电线或充电插头是否正常。 ③指示灯分为红灯/绿灯/蓝灯。 以打开上盖,取出已除菌的物品进行正常使用。 5、如在除菌过程中,需要中止作业时,请长按按键3秒,“嘀”声提 亮灯方式 模式 待机模式(通电后空载状态下) 无线充电模式 18分钟除菌模式 30分钟除菌模式 无线充电&18分钟除菌模式同时进行 无线充电&30分钟除菌模式同时进行 指示灯 红灯直亮30秒后熄灭进入待机模式 红色指示灯呈直亮状态 绿色指示灯呈直亮状态 蓝色指示灯呈直亮状态 指示灯呈红绿色混光直亮状态 指示灯呈红蓝色混光直亮状态 示后,绿/蓝色指示灯熄灭,作业中止。此时可以正常开盖取出 盒中物品。 6、除菌开始前,往盒中香薰孔内滴入2或3滴香水即可在除菌过 程中同时对盒中物品进行香薰除菌。 7、开盖自动关闭紫外线功能 磁吸开关 听到提示音,请尝试移动手机位置,以确保手机的无线充电接收部位与上盖 1、除菌盒工作时,开盖后自动关闭紫外线灯,防止对人体及眼睛 产生危害。 2、除菌盒工作时,闭合后将自动打开紫外线灯进行除菌。 充电标志对准。 3.充电过程如手机被拿起,则充电中止;无线充电与除菌功能可同时作业。 注意事项: 温馨提示 ※请勿自行拆卸本产品。 ※最多两到三滴香水即可产生充分的香薰效果,请勿滴入过量香水。 ※请勿在高温或潮湿环境下使用本产品,请远离火源和水。 ※请勿使用含酒精的香水(如花露水等),避免对硅胶材质的手机 ※本产品仅适用于支持无线充电功能的手机充电。 表面产生不良效果。 ※如手机无内置无线接收功能请另行购买无线充电接收器配合使用。 ※如手机不支持无线快充功能,则将自动调整适应为手机自身充电效率。 ※如果在除菌的过程中,上盖被打开,则除菌作业暂时挂起,紫外 ※手机背面充电接触面不能带有金属物质,如铁片、指环、金属保护壳等。 线灯将会自动熄灭,以确保不会对盒外的人体造成不必要的损 害;上盖闭合后,紫外线灯重新亮起,作业恢复。 ※如果长期未使用此产品,则开始除菌时,紫外灯可能会有一个预 热过程,时长大约在十秒之内,预热完成后紫外线灯会自动亮起。 无线充电 产品通电后默认无线充电模式,指示灯为红色,空载状态下直亮 30秒后熄灭进入待机状态。无线充电工作状态是红色指示灯呈直 亮显示。 1.确保产品上盖处于闭合状态,将手机屏幕朝上,背部无线充电接收部位对准 充电标志放下,(手机的无线充电接收部位一般在手机的背面的中间位置)。 2.无线充电模块正常检测手机时,将会发出“滴”的一声提示,表示手机放置正 确。等待约1到2秒后,手机屏幕将会出现充电提示,手机充电开始。如果没有 模式。 Thank you for purchasing the Mobile Phone Wireless Charging Sterilizing Box . Please read the instructions carefully before using this product. Specification Product name:Mobile Phone Wireless Charging Sterilizing Box Input:5V/2A;9V/2A Model:OJD-L03 Wireless Output:10W(Max) UV light output:2W(Max) Size:210*120*62MM Weight:300g Material:ABS+PC Color:White Rated frequency:110-205KHz Wireless charge conversion rate:73% Transmission distance:≤6MM Product list Mobile Phone Wireless Charging Sterilizing Box Operating instruction Mobile phone wireless charging sterilizing box x1 Type-C cable(1M)x1 Instructions x1 Dropper x2 Quick Guide 1、Plug in the equipped data cable, switch on the power supply, and the product will be in the default wireless charging mode after energizing. 中国制造 3、After the disinfection is completed in 18 or 30 minutes, the built-in buzzer will beep three times continuously. 4、Aromatherapy disinfection function: before disinfection, use the equipped straw to drip 2 or 3 drops of perfume into the aromatherapy hole in the box for aromatherapy disinfection. the lid. There are two disinfection modes: ①18-minute disinfection mode: press the button on the top of the lid for a short time, the buzzer will sound "beep", the green indicator light will light up and enter the 18-minute disinfection mode。 ②30 minutes disinfection mode: press the button on the top of the lid for 1、Place cell phones or other items to be sterilized in a box and close the lid。 2、Disinfection mode in 18 minutes: press the button on the top of the cover for a short time, and the built-in buzzer will beep "beep", the green indicator will be on, and the ultraviolet light in 5、Wireless charging function: the mobile phone can be charged wirelessly by placing it in the middle mark of the upper cover. Under the working state of wireless charging, the red indicator light will be on. 6、Wireless charging can be operated in the same time with disinfection mode. When working at the same time, the key indicator light will be displayed as " the box will light up for disinfection. When the buzzer continuously beeps "beep" for three times, the disinfection will be finished。 3、30 minutes disinfection mode: press the button on the top of the lid for two short times, and the built-in buzzer will beeps "beep" for two times. The blue indicator light will be in a straight state. At the same time, the ultraviolet light in the box will light up for disinfection.When the red and green" or "red and blue". buzzer continuously beeps "beep" for three times, the disinfection will be finished。 Detailed instructions: 4、Complete disinfection: the whole disinfection process is 18 minutes or 30 minutes. After the Put through power supply ①Before use, please insert the equipped data cable, turn on the power supply, the product will be powered on by default wireless charging mode, the indicator light will be red, it will stay on for 30 seconds in the no-load state, then it will be off and put into standby state. ②If the red light is not on, please check whether the charging cable or charging plug is normal. ③The indicator lights are red/green/blue。 disinfection operation is completed, the buzzer will continuously sound "beep " three times, indicating the automatic end of the operation. 5、In the process of disinfection, if you need to stop the operation, please press the button for 3 seconds. After the "beep" sound, the green/blue light will go out and the operation will be stopped. At this point, you can normally open the lid and take out the contents of the box。 6、Before disinfection begins, drop 2 or 3 drops of perfume into the aromatherapy hole in the box to carry out aromatherapy disinfection on the items in the box at the same time in the the indicator light will be red. 2、Put the items that need to be sterilized into the sterilizing box and close Disinfection model Standby mode (no load after power on) Indicator light The red light goes on for 30 seconds and then disinfection process. 7、Open cover automatically closes uv function. goes off into standby mode Wireless charging mode The red indicator light kept on 18-minute sterilization mode The green indicator light kept on 30-minute sterilization mode The blue indicator light kept on Wireless charging & 18-minute disinfection mode simultaneously two short times, then the buzzer will sound "beep" and "beep", the blue Wireless charging &30 minutes disinfection indicator light will light up, and enter the disinfection mode for 30 minutes. mode simultaneously The indicator light is red and green The indicator light is red and blue Magnetic switch 1.When the sterilizing box is working, it will automatically close the uv light after opening the cover to prevent harm to human body and eyes. 2.When the sterilizing box is working, it will automatically turn on the uv light to sterilize. Warm prompt ※A maximum of two or three drops of perfume can produce full aromatherapy effect. Do not drop excessive perfume。 ※Do not use perfume containing alcohol (such as toilet water, etc.) to avoid adverse effects on the surface of the silicone phone. ※If the upper cover is opened during the disinfection process, the disinfection operation will be suspended temporarily and the ultraviolet lamp will be automatically extinguished to ensure that unnecessary damage will not be caused to the human body outside the box. After the top cover is closed, the UV light is turned on again and the operation is resumed. ※If the product has not been used for a long time, the UV light mayhave a warm -up process when disinfection begins, it's about 10 seconds long. After the warm-up, the UV light will automatically light up. Wireless charging and the phone will start charging. If you don't hear the beep, try moving the phone to make sure the wireless charging receiving area of the phone is aligned with the charging sign on the top cover 3.If the phone is picked up during the charging process, the charging will be terminated; Wireless charging and degerming functions can work at the same time. Matters needing attention: ※Do not disassemble the product by yourself。 ※Do not use this product in high temperature or humid environment, please keep away from fire and water。 ※This product is only suitable for mobile phone charging which supports wireless charging function。 ※If the phone does not have built-in wireless reception function, please purchase a wireless charging receiver separately for use。 ※If the mobile phone does not support the wireless quick charge function, it will automatically adjust to the charging efficiency of the mobile phone itself。 ※The charging contact surface on the back of the mobile phone shall not contain metal substances, such as iron sheet, ring and metal protective case。 When the product is powered on, the default mode is wireless charging, and the indicator light is red. In no-load state, the device will be in standby state after 30 seconds. The working state of wireless charging is shown directly by the red indicator light 1.Make sure the top cover of the product is closed, turn the phone's screen up, and lower the back wireless charging receiving area toward the charging sign (the wireless charging receiving area of the phone is generally in the middle of the back of the phone). 2.When the wireless charging module detects the phone normally, it will give a "deep" prompt, indicating that the phone is placed correctly. After waiting for about 1 to 2 seconds, the phone will display a charging prompt on the screen Made in China ...
Purchase answer to see full attachment
Student has agreed that all tutoring, explanations, and answers provided by the tutor will be used to help in the learning process and in accordance with Studypool's honor code & terms of service.

Final Answer

Attached.

Mobile Phone Wireless Charging Sterilizing Box Operating instruction

Product list
Mobile phone wireless charging sterilizing box x1
Type-C cable (1M) x1
Instructions x1
Dropper x2
Quick Guide
1. Plugin the power cable provided and switch on the power from the socket. The device
will be on and in the wireless charging mode. The indicator light will be red.
2. Gently place the item to sterilize into the sterilizing box and close the lid. There are two
disinfection programs that one can choose from:
❖ The 18-minute disinfection program – Press the button on the cover lid
continuously. This will set the device in the 18-minute disinfection program and
will make a “beep” sound and give a green indicator.
❖ The 30 minutes disinfection program – press the button on the cover of the lid for
two continuous times to set this program. The device will produce two "beep"
sounds, and a blue indicator light will show from the indicator.
3. After the disinfection is completed in 18 or 30 minutes, the built-in buzzer will beep for
three continuous times.
4. Aromatherapy disinfection function - before disinfection, use the provided straw to add 2
or 3 drops of perfume into the aromatherapy hole in the box for aromatherapy
disinfection.
5. Wireless charging function - the device can be used to wirelessly charge a mobile phone
by placing it in the middle mark of the upper cover. Under the working state of wireless
charging m...

CristinaP (13822)
UIUC

Anonymous
The tutor was pretty knowledgeable, efficient and polite. Great service!

Anonymous
Heard about Studypool for a while and finally tried it. Glad I did caus this was really helpful.

Anonymous
Just what I needed… fantastic!

Studypool
4.7
Trustpilot
4.5
Sitejabber
4.4