How to judge when to replace piston rings in a Model A Ford versus re-boring the cylinders

User Generated

ebae

Other

Description

How to judge when one can just replace the piston rings in a Model A Ford engine versus having to re-bore the cylinders?

User generated content is uploaded by users for the purposes of learning and should be used following Studypool's honor code & terms of service.

Explanation & Answer

Though pistons can often be salvaged when remanufacturing an engine, sometimes they have to be replaced. The original pistons may have worn or damaged ring grooves, wrist pins or skirts, or they may have cracks. New pistons may also be necessary if the cylinders have too much taper wear and the block has to be bored to oversize. Or, maybe you just don't want to reuse the original pistons if you're building a performance engine or a high load engine like a diesel.

Pistons can fail any number of ways. The worst kind of failure is a catastrophic explosion that spews shrapnel inside the engine. A cast piston can shatter like a grenade if it hits a valve at high rpm, or a solid object is sucked into the combustion chamber. The underlying cause may have been a broken timing chain or belt, the head of a valve snapping off because of fatigue failure (which can be caused by a lack of concentricity between the valve guide and seat), or a valve keeper breaking off the top of the valve stem or pulling through the spring retainer. In a performance engine, a close encounter between a valve and piston may occur if the engine overrevs causing the valves to float, or a valve spring breaks.

Burned and broken pistons are another problem you'll often discover when the engine is torn down. The underlying cause here is often engine overheating, detonation (spark knock) and/or preignition. This includes problems that may be lurking in the vehicle's cooling system, fuel delivery system, ignition system and emission controls.

Detonation can be caused by low octane fuel, over advanced spark timing, a defective or plugged EGR valve, a lean fuel mixture (dirty fuel injectors or a weak fuel pump), a buildup of carbon deposits in the combustion chamber, and engine overheating. Detonation can occur when fuel ignites spontaneously from excessive heat and pressure. The sudden increase in pressure can really hammer the pistons and rings causing them to break. Detonation can also damage the rod bearings and head gasket, too.

Preignition occurs when a hot spot inside the combustion chamber ignites the fuel before the spark plug fires. This also causes elevated pressures and temperatures that can sometimes burn a hole right through the top of a piston! Preignition is most often due to engine overheating and lean fuel mixtures, but can also result if the wrong heat range spark plugs (too hot) are used.

Replacing detonation- or preignition-damaged pistons in a customer's engine may temporarily return the engine to service. But the new pistons will likely suffer the same fate as the old ones unless the conditions that were causing the problems are diagnosed and corrected.

Scuffing is another condition that can damage pistons. Scuffing is often the result of overheating, but loss of lubrication, detonation and preignition can also be contributing factors. When an engine runs hot, the pistons swell. This reduces the clearance between the piston and cylinder walls. The cylinder bore can also distort adding to the problem. If the piston scuffs, it will wipe metal off the side of the piston.

Where the scuffing occurs will give you a clue as to what might have caused it. When overheating is involved, the scuffing will be primarily on the upper ring lands and on the sides near the wrist pins. There may also be oil carbon and lacquer burned onto the underside of the piston indicating it got too hot. Scuff marks on the lower skirt area often indicates a lack of lubrication (check the oil pump and pickup screen). Scuff marks on the edges or corners of the thrust sides of the piston may be the result of bore distortion. Scuffing on both thrust sides would indicate binding in the wrist pin.

Normal wear also takes its toll on pistons. The constant pressure and reciprocating motion in the cylinder bore causes wear on the piston skirt as well as the wrist pin bosses and ring lands. Elevated temperatures and high loads cause microwelding between the rings and lands, resulting in rapid land wear.

Sometimes a wrist pin will work loose and chew into the cylinder with each stroke of the piston. The underlying cause here may have been improper installation of the retaining lock rings on a full floating wrist pin, improper fit or installation of a pressed-in wrist pin, a twisted or bent connecting rod, excessive thrust end play in the crankshaft or taper wear or misalignment in the crankshaft rod journal.

PISTON DIAGNOSIS
Piston slap is a classic symptom of too much clearance between the pistons and cylinder bores. Piston slap is most audible when a cold engine is first started because clearances are greatest then. This doesn't necessarily mean the pistons are worn because some new engines will slap a bit when first started. But if the slap doesn't go away as the engine warms up, it usually means the pistons and/or cylinders are worn. A compression test and/or leakdown test can be used to confirm the diagnosis.

A cracked piston or one with a hole in it will usually signal its presence with a plume of blue smoke in the exhaust. There will also be excessive blowby into the crankcase, which will be evident if the PCV valve is temporarily removed while the engine is idling. A power balance test, compression check or leakdown test can be used to isolate the problem to a specific cylinder.

PISTON REPLACEMENT
Any pistons that are worn or damaged must be replaced. In most cases, if one piston is bad, the others are too so all would be replaced as a complete set. Many pistons that appear to be in good condition and show no signs of scuffing may still have to be replaced because the upper ring lands are worn. If a piston with worn ring lands is reused, the rings won't seal properly and the engine will use oil. Wear or looseness in the wrist pin area would also call for replacement.

Another reason to replace pistons would be to change the stock compression ratio (as when using different heads, aftermarket heads, or when building a performance motor), or to increase engine durability. Stock cast pistons are fine for everyday driving but may lack the strength to handle higher than stock horsepower in a modified engine. Upgrading to hypereutectic pistons or forged pistons in such a case would probably be necessary.

The safest bet is to replace pistons with ones that are the same material as the original, or better. Many late model engines today are factory-equipped with hypereutectic pistons. Switching to cheaper cast pistons may be asking for trouble.

Hypereutectic pistons have a higher silicon content (typically 16 to 20 percent versus 8 to 11 percent for a standard piston), which makes them harder, more wear resistant and much stronger than ordinary cast alloys. Consequently, hypereutectic pistons are better able to resist ring pound out and scuffing. They also expand less than standard cast alloys, which allows them to be assembled with closer tolerances (helps reduce noise)


Anonymous
Just what I needed. Studypool is a lifesaver!

Studypool
4.7
Trustpilot
4.5
Sitejabber
4.4

Similar Content

Related Tags