i need help with lab

User Generated

nyfnuyv

Engineering

Description

i need some one do the lab the second pic what is miss you should to do it add it to the lab

Unformatted Attachment Preview

Morgan State University Department of Electrical and Computer Engineering EEGR 317 Microelectronics Credits – 4 LAB 4 : NMOS Common-Source Ampli ier and NPN Common-Emitter Ampli ier Lab Due: May 10, 2017 Objective: To study NMOS-based common- source (CS) and NPN-based common-emitter (CE) ampli iers by: • Completing the DC and small-signal analysis based on their theoretical behavior. • Simulating the ampli iers to compare the results with the paper analysis. • Implementing the circuits in an experimental setting, taking measurements, and comparing its performance with theoretical and simulated results. • Measuring their output resistance. • Qualitatively seeing the impact of transistor-to-transistor variations. Materials: 1. 2. 3. 4. Laboratory setup, including breadboard 1 enhancement-type NMOS transistor (e.g., 2N7000) and 1 NPN-type bipolar transistor (2N2222) 3 large (e.g., 47µF) capacitors Several wires and resistors of varying sizes Part 1:Design and Simulation of NMOS Common-Source Ampli ier Consider the circuit above. Design the ampli ier to achieve a small-signal gain of at least AV = 5V /V . Use supplies of V+ = V = 15V , Rsig = 50⌦, RL = 10k⌦, RG = 10k⌦, and design the circuit to have ID = 1mA. Obtain the data sheet for the NMOS transistor that will be used. 1 DC Operating Point Analysis • Using a DC model of the circuit, (the three coupling capacitors are replace with ”large-valued” capacitors that create open circuits and you may also omit vsig , Rsig , and RL from the circuit), you have enough information to calculate VOV = VGS Vtn . Calculate and write down the value of VOV and gm . What is the value of VGS ? Remember: Your actual transistor will have a value of Vtn that will vary from his nominal value, which will alter your measurement results slightly. • Calculate r0 . • You now have enough information to calculate RS . Calculate and show your calculations for RS . Is this value available in your kit or can it be created by combining resistors? • Note: At this stage we do not know neither VDS nor RD . AC Analysis • Replace the circuit with its small-signal model. In the small-signal model, the capacitors will be at short circuits (what happens to RS ?) and replace V+ with an AC ground. What happens to V ? Label the gate of the transistor as vi , i.e., the small-signal voltage at the input. • What is the ratio of vi /vsig ? How would you approximate it in further calculations? • Derive the expression for Av = v0 /vi . What is the value of RD that produces a small-signal focus gain of at least AV = 5V /V ? Is the value for RD available in your kit or can it be created by combining resistors? • What is the DC voltage at the drain? Does this satisfy the assumption that the transistor should be operating in the saturation region? Explain. • What is the output resistance, Ro ? Simulation • Simulate your circuit. Use capacitive values CC1 = CC2 = CS = 47µF , and the values of RS and RD based on your preceding calculations. Use a 10mVpk pk , 1kHz sinusoid with not DC component applied at vsig . • From your simulation, report the DC values of VGS , VDS , and ID . How closely do they match your calculations? (Remember: The simulator has his own more complex model of the real transistor, so there should be some small variations.) • From your simulation, report AV . How closely does it match your calculations? Part 2:Prototyping • Assembled the circuit onto your breadboard using the speci ied component values and those just calculated. Note that Rsig represents the output resistance of the function generator, and therefore you should not include in your circuit. Part 3:Measurement • DC bias point measurements: Using a digital multimeter, measure the DC voltages of your circuit at the gate (VG ) , source (VS ), and drain (VD ) of your transistor. • AC measurements: Using a function generator, apply to your circuit a 10mVpk pk , 1kHz sinusoid with no DC component. (Note: Some function generators allowed only implicit small as 50mVpk pk . If this is the case, use that value instead. Some distortion may occur in the output waveform.) 2 • Using an oscilloscope, generate plots of vo and vi vs. t. • Output resistance Ro : Replace RL with a 1M ⌦ resistor and repeat the AC measurement. What is the amplitude of the output waveform? Adjust RL until you ind a value such that the amplitude of the output waveform is approximately 50% of what is was for the 1M ⌦ load. This new value of RL is the output resistance Ro . How does it compare to the value calculated earlier? Hint: It cannot be greater than the value of RD . • Using a digital multimeter, measure all resistors to three signi icant digits. Part 4:Post-Measurement Exercise • Calculate the values of VGS and VDS that you obtained in the lab. How do they compare to your pre-lab calculations? Explain your discrepancies. • Based on the measured values of VD and VS and your measured resistor values, what is the real value of ID based on your lab measurements? • What is the measured value of Av ? How does it compare to your pre-lab calculations? Explain any discrepancies. • Hint: The single biggest source of variations from your pre-lab simulation results will be due to variations in the transistor threshold voltage Vtn . Remember: Its value would be somewhere within the range indicated on the transistor data sheet. Part 5: Design and Simulation of Common-Emitter Ampli ier Consider the circuit shown below. Design the ampli ier to achieve a small-signal gain of at least AV = 200V /V . Use supplies of V+ = V = 15V , Rsig = 50⌦, RL = 10k⌦, RB = 10k⌦, and design the circuit to have IC = 1mA. Although there will be variations from transistor to transistor, you may assume a value of of 100 in your calculations. Obtain the data sheet for the NPN transistor that will be used. 3 DC Operating Point Analysis • Using a DC model of the circuit, (the three coupling capacitors are replace with ”large-valued” capacitors that create open circuits and you may also omit vsig , Rsig , and RL from the circuit), calculate and write down the value of IB and IE . What is the value of VB ? • Calculate a value for RE that produces a base-emitter voltage drop value of 0.7V . What is VE ? • You now have enough information to calculate RS . Calculate and show your calculations for RS . Is this value available in your kit or can it be created by combining resistors? • Note: At this stage we do not know neither VCE nor RC . AC Analysis • Replace the circuit with its small-signal model (VA is large, so you may ignoore ro ). In the small-signal model, replace the capacitors with short circuits (what happens to RE ?) and replace V+ with an AC ground. What happens to V ? Label the base of the transistor as vi , i.e., the small-signal voltage at the input. What are the values of gm and r⇡ ? • What is the ratio of vi /vsig ? Can you approximate it? • Derive the expression for Av = v0 /vi . What is the value of RC that produces a small-signal focus gain of at least AV = 200V /V ? Is this resistor value available in your kit or can it be created by combining resistors? • What is the DC voltage at the collector? Does this satisfy the assumption that the transistor should be operating in the active region? Explain. • What is the output resistance, Ro ? Simulation • Simulate your circuit. Use capacitive values CC1 = CC2 = CE = 47µF , and the values of RE and RC based on your preceding calculations. Use a 10mVpk pk , 1kHz sinusoid with not DC component applied at vsig . • From your simulation, report the DC values of VBE , VCE , IB , IC , and IE . How closely do they match your calculations? (Remember: The simulator has his own more complex model of the real transistor, so there should be some small variations.) • From your simulation, report AV . How closely does it match your calculations? Part 6:Prototyping • Assembled the circuit onto your breadboard using the speci ied component values and those just calculated. Note that Rsig represents the output resistance of the function generator, and therefore you should not include in your circuit. Part 7:Measurement • DC bias point measurements: Using a digital multimeter, measure the DC voltages of your circuit at the base (VB ) , emitter (VE ), and collector (VC ) of your transistor. • AC measurements: Using a function generator, apply to your circuit a 10mVpk pk , 1kHz sinusoid with no DC component. (Note: Some function generators allowed only implicit small as 50mVpk pk . If this is the case, use that value instead. Some distortion may occur in the output waveform.) 4 • Using an oscilloscope, generate plots of vo and vi vs. t. • Output resistance Ro : Replace RL with a 1M ⌦ resistor and repeat the AC measurement. What is the amplitude of the output waveform? Adjust RL until you ind a value such that the amplitude of the output waveform is approximately 50% of what is was for the 1M ⌦ resistor. This new value of RL is the output resistance Ro . How does it compare to the value calculated earlier? Hint: It cannot be greater than the value of RC . • Using a digital multimeter, measure all resistors to three signi icant digits. Part 8:Post-Measurement Exercise • Calculate the values of VBE and VCE that you obtained in the lab. How do they compare to your pre-lab calculations? Explain your discrepancies. • Based on the measured values of VB , VC , and VE and your measured resistor values, what is the real value of all currents based on your lab measurements? How does it compare to your pre-lab calculations? • Based on the actual value of the measured currents, what is the actual value or for your transistor? • What is the measured value of Av ? How does it compare to your pre-lab calculations? Explain any discrepancies. • Hint: The single biggest source of variations from your pre-lab simulation results will be due to variations in . 5 are prototypes No written equi allowed Stommation Simulations t Prototypes must have Save source Voltage
Purchase answer to see full attachment
User generated content is uploaded by users for the purposes of learning and should be used following Studypool's honor code & terms of service.

Explanation & Answer

Attached.

Name

1

Name
Instructor
Course
Date
NMOS Common Source Amplifier and NPN Common Emitter Amplifier
Design and Simulation of NMOS Common-Source Amplifier
The main aim of this lab is to design an NMOS common source amplifier that has a
voltage gain of -5V/V for small signals. Small signals are signals whose amplitude is small in
such a way that it does not significantly affect the operating Q-point of the amplifier. Two source
voltages are used +15V and -15V. The gate and load resistors are also given as RG=RL=10kΩ.
The circuit is designed based on the schematic shown in the figure below. The amplifier should
also have a drain current, ID, of 1mA. For the design process, 2N7000 enhancement MOSFET
transistor is used.

Name

2

Design process
a) DC Operating point analysis
When creating the DC equivalent circuit for the above Common Source NMOS transistor
amplifier, all capacitors are isolated from the circuit because they block the DC thereby
acting like open circuits. Therefore, the schematic appears as shown below

𝐼𝐷 = 𝑘(𝑉𝐺𝑆 − 𝑇𝑇𝐻 )^2
From the above equation of the NMOS output characteristics, we need to find the value
of k for our particular transistor, 2N7000. The data sheet gives a threshold voltage of
0.8V.Using the NMOS output characteristics (ID=1000mA, VGS=8V) and (ID=200mA,
VGS=4V)
𝑘=

𝐼𝐷
200
=
= 19.53𝑚𝐴/𝑉 2
2
(𝑉𝐺𝑆 − 𝑉𝑇𝐻 )
(4.0 − 0.8)2
1

Therefore for the desired value of ID=1mA, VGS=√19.53 + 0.8 = 1.027𝑉
Also,
𝑟𝑜 =

1
𝑉𝐴
100
=
=
= 100𝑘Ω
𝜆𝐼𝐷 𝐼𝐷 1𝑚𝐴

Name

𝑉𝑂𝑉 = 𝑉𝐺𝑆 − 𝑉𝑇𝐻
𝑉𝑂𝑉 = ...


Anonymous
Very useful material for studying!

Studypool
4.7
Trustpilot
4.5
Sitejabber
4.4

Related Tags