Anonymous
timer Asked: Apr 28th, 2020

Question Description

I need helping finding the subnet’s and the IP addresses. I have been trying to figure out how to find them

Unformatted Attachment Preview

CCNA: Network Basics Skills Assessment – Student Training Exam Topology Assessment Objectives Part 1: Develop the IPv4 Address Scheme (15 points, 20 minutes) Part 2: Configure Device IPv4 and Security Settings (30 points, 20 minutes) Part 3: Test and Verify IPv4 End-to-End Connectivity (8 points, 10 minutes) Part 7: Use the IOS CLI to Gather Device Information (10 points, 10 minutes) Scenario In this Skills Assessment (SA) you will configure the devices in a small network. You must configure a router, switch and PCs to support IPv4 connectivity. You will configure security on the router. You will test and document the network using common CLI commands. Required Resources • Packet Tracer © 2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 1 of 6 CCNA: Network Basics SA Exam Part 1: Develop the IPv4 Addressing Scheme Given an IP address and mask of __10.10.128.0 /17_____________ (address / mask), design a VLSM IP addressing scheme that satisfies the following requirements. Network address/mask and the number of hosts for Subnets A and B will be provided by your instructor. Subnet Number of Hosts Subnet A 1000 Subnet B 120 The 0th subnet is used. No subnet calculators may be used. All work must be show in Excel. • The router interface will use the FIRST IP address in the subnet, • The switch management VLAN will be assigned the SECOND usable IP address. • The host computer will use the LAST usable address. Write down the IP address information for each device: Device IP address Subnet Mask Gateway PC-A R1-G0/0 N/A R1-G0/1 N/A S1 PC-B © 2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 2 of 6 CCNA: Network Basics SA Exam Part 2: Initialize and Reload Devices Step 1: Initialize and reload router and switch. Provide the commands that will erase the startup configurations and VLANs from the router and switch and reload the devices. Task IOS Command Erase the startup-config file on the Router. Reload the Router. Show routing table Delete the vlan.dat file on the Switch Show interface brief © 2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 3 of 6 CCNA: Network Basics SA Exam Part 3: Configure Device IPv4 and Security Settings Step 1: Configure host computers Configure the host computers according to the IP scheme Step 2: Configure R1 Configuration tasks for R1 include the following: Task Specification Disable DNS lookup Encrypt all passwords in the running configuration Router name EdgeRTR Encrypted privileged exec password ciscoenpw Console access password consolepw Configure SSH for remote Access Username: SSHAdmin Encrypted Password: class123 Domain: ct.com Modulus: 2048 MOTD Banner Authorized Access Only Interface G0/0 Set the description: LAN-A Set the Layer 3 IPv4 address Activate Interface Interface G0/1 Set the description: LAN-B Set the Layer 3 IPv4 address Activate Interface © 2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 4 of 6 CCNA: Network Basics SA Exam Step 3: Configure S1. Configuration tasks for S1 include the following: Task Specification Switch name SW_LAN-B Disable DNS Lookup Configure DNS Domain Name ct.com Configure Management Interface (SVI) Set the Layer 3 IPv4 address Encrypt all passwords in the running configuration Encrypted privileged exec password ciscoenpw Console access password consolepbw MOTD Banner Authorized Access Only Configure Telnet for remote access (all lines) Password: vtypw Configure the switch’s default-gateway Part 4: Test and Verify IPv4 End-to-End Connectivity Step 1: Verify network connectivity. Use the ping command to test connectivity between all network devices. Use the following table to methodically verify connectivity with each network device. Take corrective action to establish connectivity if a test fails: From To PC-A EdgeRTR, G0/0 PC-A EdgeRTR, G0/1 PC-A S1 VLAN 1 PC-A PC-B PC-B EdgeRTR, G0/1 PC-B EdgeRTR, G0/0 PC-B S1 VLAN 1 PC-A SSH to EdgeRTR PC-A Telnet to S1 IP Address Ping Results In addition to the ping command, what other command is useful in displaying network delay and breaks in the path to the destination? (5 point) © 2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 5 of 6 CCNA: Network Basics SA Exam © 2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 6 of 6 ...
Student has agreed that all tutoring, explanations, and answers provided by the tutor will be used to help in the learning process and in accordance with Studypool's honor code & terms of service.

This question has not been answered.

Create a free account to get help with this and any other question!

Similar Questions
Related Tags

Brown University





1271 Tutors

California Institute of Technology




2131 Tutors

Carnegie Mellon University




982 Tutors

Columbia University





1256 Tutors

Dartmouth University





2113 Tutors

Emory University





2279 Tutors

Harvard University





599 Tutors

Massachusetts Institute of Technology



2319 Tutors

New York University





1645 Tutors

Notre Dam University





1911 Tutors

Oklahoma University





2122 Tutors

Pennsylvania State University





932 Tutors

Princeton University





1211 Tutors

Stanford University





983 Tutors

University of California





1282 Tutors

Oxford University





123 Tutors

Yale University





2325 Tutors