Telecommunication
Question Description
- If a cable (MEDIUM) has been adapted to have a fmin = 0.5 GHz and fmax= 2 GHZ, (G is for GIGA). Which of the following statements are NOT correct?
- It is possible to change the BW of the media if we change the coding and modulation technique.
- A signal with BW = 1 GHZ will be severely attenuated when transmitted by this medium
- The BW of the media can’t be calculated however, the capacity and the speed are easily calculated.
- The BW can’t be increased by improving equalization and by reducing the noise on the line.
- A signal of 5,000 KHZ will have no problem moving along this cable
Briefly ( i.e. ~ 50 words) explain the choices that you believe are NOT CORRECT and why. No explanation à NO credit! (if more than one answer is NOT correct you tell me which ones are right and why… PLEASE Only explain the one(s) that is (are) NOT CORRECT) (4 points)
- Which of the following statements (or statement is) are NOT CORRECT about Signal to noise ratio (S/N) or Carrier to Noise (C/N) (4 points)
- We must increase both, the signal and the noise power so there is no need for an equalizer.
- The lower the Signal-to-Noise ratio the worst it is for telecomm.
- When the signal has low power and the noise has high power, the C/N (S/N) ratio is low.
- C/N ratio is better when we diminish the noise power so the signal can be better differentiated
- C/N ratio could not be calculated or controlled at all because the average noise and the signal level can’t be measured.
- C/N ratio is directly proportional to the BW of the media and then directly proportional to the media Capacity.
- Which of the following statements are correct?(if any) (2 points)
- Broadband can’t transmit Voice, Video and Data at the same time
- Baseband can transmit Voice, Video and Data at the same time
- Broadband can divide the channel in many phase slots so it can transmit different signals in different phases of the wave.
- Baseband is capable of transmitting voice, data and video however it must divide the BW is different frequencies to allow the transmission.
- Broadband and baseband use FDM and TDM respectively to transmit signals.
- If 5000 equal signals are transmitted in 50 seconds. The Period (In seconds or milliseconds) and frequency (in KHertz) of each signals is____ (Show your calculations or no credit) (1 point)
- T= 1 second and 0.1 KHz
- T = 0.01 milliseconds and 0.01 KHz
- T= 0.01 milliseconds and 100 KHz
- T= 0.01 seconds and 10 KHz
- None of the above
- Which of the following factors do(es) not affect the “transfer rate” in a connection (1 point)
- The receiver’s ability to receive the data
- The transmitter’s ability to put data on the media
- The amount of or machines connected to the server demanding data (i.e. The server you are downloading from)
- The noise of the media involved in the connection
- The size of the file transmitter
- A synchronous transmission uses the sequence “1100100100100100000000000” to synchronize the equipment and the sequence “0011011011011011111111111” to let the equipment know the transmission has ended. In this transmission line 10,000 bits of information are transmitted at once (NOT including the above sequences which are added for sync purposes) what is the efficiency of this synchronous transmission channel assuming there is no noise?Explain, show your calculations (2 points) give your efficiency in percentage with 4 digits’ precision (i.e.90.9193%)
- Your transmitter can transmit up to 5 Gigabits/second, your receiver can receive up to 7 Gigabits/second and the Capacity of the channel is 10 Gigabits/second. Which of the following statements are wrong IF any? (Assume there is no noise, and when one change is mentioned, assume the other parameters are maintained the same)
- Changing the transmitter to a one capable of transmitting 7 Gigabits/second will increase the Bandwidth of the channel.
- Changing the receiver to a one capable of receiving 15 Gigabits/second will increase the speed of the channel to 15 Gigabits/second.
- If another media with capacity 15 Gigabit/second is used this will ensure to increment the BW to 15 Gigabits/second.
- Changing the transmitter to a one capable of transmitting 10 Gbits/second will optimize the transmission from beginning to end.
- Changing ALL (transmitter, receiver and media) to 10 gigabits/second in capacity will ensure the Bandwidth is 10 GHZ per second.
Briefly explain the NOT correct choices only (Even if you have the correct choice, if your explanation is not technically correct à no credit)
Briefly explain your choices (Please explain only the correct statements only …. if the explanation is not technically sound à no credit)
Briefly explain your choice(s) (choices with not sound or correct explanation à no credit)
(5 points) Briefly explain your WRONG choices only (no sound explanation for your choices à no credit)
This question has not been answered.
Create a free account to get help with this and any other question!
Brown University
1271 Tutors
California Institute of Technology
2131 Tutors
Carnegie Mellon University
982 Tutors
Columbia University
1256 Tutors
Dartmouth University
2113 Tutors
Emory University
2279 Tutors
Harvard University
599 Tutors
Massachusetts Institute of Technology
2319 Tutors
New York University
1645 Tutors
Notre Dam University
1911 Tutors
Oklahoma University
2122 Tutors
Pennsylvania State University
932 Tutors
Princeton University
1211 Tutors
Stanford University
983 Tutors
University of California
1282 Tutors
Oxford University
123 Tutors
Yale University
2325 Tutors